Analytical Electronics Services Pvt Ltd

Power Quality Analyzer

Dranetz-BMI PX5 & PP-4300 : Power Quality Analyzers

Dranetz-BMI PX5 & PP-4300 for rental

• (4) differential inputs, 1-600 Vrms, AC/DC, 0.1% rdg + 0.05% FS, 256 samples/cycle, 16 bit ADC
• (4) inputs with CTs 0.1-6000 Arms CT-dependent, AC/DC, 0.1%rdg + CTs, 256 samples/cycle, 16 bit ADC
• 1 MHz High Speed Sampling, 14 bit ADC, 1% FS
• 256 samples/cycle; 1/2 cycle RMS steps (1)
• L-L, L-N, N-G RMS Variations: Sags/swells/interruptions)
• W, VA, VAR, TPF, DPF, Demand, Energy, etc.
• IEEE 1459 Parameters of distorted and unbalanced
• Harmonics/Interharmonics per IEC 1000-4-7
• THD/Harmonic Spectrum (V,I,W) to 63rd
• TID /Interharmonic Spectrum (V,I) to 63rd
• Flicker per IEC 1000-4-15 (Pst,Plt,Sliding Plt) Compliance
• IEEE 1159, IEEE 519, IEEE 1453
• IEC 61000-4-30 Class A and EN50160
• flicker according to IEC 61000-4-15; measures electrical harmonics according to IEC 61000-4-7
• CURRENT PROBE/CT avail with different range 10A,1000A,3000A

Fluke 41 / 40 : Power Harmonics Meter

Fluke 41 / 40 for rental

• Single Phase Hand Held unit any Electrical engineer can operate it.
• Measure the voltage and current (via the 500A current transformer supplied) of the circuit under test. It can then display the voltage, current or power as a waveform, a bargraph of the harmonics or as a digital display.
• Measured current. Crest factor, peak/rms value, %THD of current referenced to fundamental (%THD-F), or total rms (%THD-R) of current.
• Watts, Volt-Amps, power factor (total) and displacement power factor of fundamental of Single-phase power

Test Equipment to Rent...

Dranetz-BMI 626 : Universal Disturbance Analyzer

DranetzBMI 626 for rental

• Universal Disturbance Analyzer

Dranetz-BMI 606 : Power Line Disturbance Analyzer

Dranetz 606 for rental

• Power Line Disturbance Analyzer

Thermal Energy Analysis Tools

IR Camera is professional tools to diagnose electrical and other no. of parameters. This is right tools for some of following application:

Utilities

Utilities depend on thermography to avoid costly failures in power generation, transmission and distribution as infrared cameras help find anomalies before trouble strikes and service is affected.

A bad connection on a transmission line shows up as a clear hot spot in the infrared image. A bad connection results in increased resistance and the current flow generates excessive temperature that can easily be detected with infrared thermography. If not attended to this connection might break, resulting in loss of power.

Thermal Imaging for Manufacturing Industries

Mechanical Equipment

Some examples of mechanical equipment where thermography is used:

• Pumps (overheated connections, fuse problems, overloaded electrical cables etc)
• Process valves (open, closed, leakage)
• Storage tanks (sludge levels)
• Pipelines (check if and where there are anomalies, for example locate build up of scale etc)
• Motors (overheating bearings, misalignment, overheated windings)
• Conveyor belts (overheated bearings)
• Furnace inspections (with a special camera designed to “see through flames” for high temperature industrial furnace applications, ideal for monitoring all types of furnaces, heaters and boilers.)

Thermal Fusion image of steam leaking from a pipe due to insufficient insulation.

Electrical Equipment

Some examples of electrical equipment where thermography is used:

• Primary power source i.e. outdoor high voltage switchyard
• Switchgear
• Transformers
• Low voltage installations i.e. breaker panels, faulty electrical outlets/wall sockets
• Fuse panels
• Motor control centers (MCC)
• Electrical cabinets

Bolted connection with increased resistance results in heat conducted down the bus bar.

Thermal Imaging for Electrical Contractors

Detect Problem Areas Before the Real Problems Occur

• In production plants, office facilities, hospitals or hotels, an infrared camera instantly makes hot spots visible on a clear thermal image. You can scan electrical cabinets and components and
• survey multiple wires and connections to get an instant picture of potential trouble. Detect the problem area and repair it before real problems occur. Common electrical targets are fuses, electrical panels, bolted connections and switchgear.

Measure Temperatures in a Non-Contact Mode

• A thermal camera allows you to measure the temperature of any object you are looking at in a non-contact mode, without putting yourself in danger. A crosshair or an area in the infrared image allows you to measure either the point value or the max or min value. Detect the most diverse electrical problems instantaneously by seeing them on a thermal image.

Bolted connection with increased resistance results in heat conducted down the bus bar.

Flir i50 : Thermal Imaging Camera

Flir i50 for rental

• Wide Temperature Range — Measures from -20 °C to +350 °C targeting electrical and industrial applications
• Digital Camera — 2.3 Megapixels with built-in LED lights provides sharp images regardless of lighting conditions
• Picture in Picture (PiP) — Displays resizable IR image super-imposed over a digital image
• ± 2% Accuracy — Reliable temperature measurement
• IR Window Auto-Correction — Automatic sensitivity adjustment when inspecting high voltage through safety IR windows
• Thumbnail Image Gallery — Allows quick search of stored images
• Laser Pointer — Pinpoints the hot spot on the IR image with the real physical target
• Micro SD Card — Stores more than 2000 radiometric JPEG images
• Software makes it possible to analyze, both infrared and visual pictures captured in field, back in the office.

Fluke 63 : IR Thermometer

Photo Comming Soon...


Dranetz 606 for rental

• The fluke 63 non-contact IR Thermometer is the ideal professional diagnostic tool for the quick and accurate temperature measurement.
• These handheld portable tools enable engineer to research heating and ventilation problems, monitor the status of electrical motors and electrical panels, etc..
• Measure temperature Range : -32 °C to +535 °C

For Queries

Test Equipment to Rent...

These are the some Stock of Test & Measurement Equipments. If you are not sure about what you require, please call. We have in-house expertise that can help you work out the best solution to your problem.